MASONRY & FINISHES

Brickwork calculator

Masonry units and a geometric mortar allowance.

YOUR MEASUREMENTS

Brickwork

▦
↻ Results update as you type
YOUR ESTIMATELIVE
Units to buy
896units
Net mortar volume0.247 m³
Wall area14.4 m²
CONNECT TO COST, LABOUR & BOQ
Open BoQ ↗

An estimate for planning. Currency selection changes the display symbol only (no exchange-rate conversion). Verify measurements and product specifications before ordering.

THE FORMULAUnits = wall area / ((unit length + joint) × (unit height + joint))
ASSUMPTIONSAssumes a single leaf, uniform joints and no openings. Mortar is a simple geometric joint volume; it excludes frogs, hollow cores, bedding patterns, dry-mix conversion and waste. Confirm actual unit sizes.
UNDERSTAND YOUR ESTIMATE

How to use the brickwork calculator

This calculator helps you estimate brick quantities and geometric mortar volume for a single-leaf wall. It is intended for quantity takeoffs, early budgets and checks against a measured schedule. Start with the dimensions or quantities for one clearly defined item of work. Enter values in the units shown beside each field; millimetres and metres are not interchangeable.

Assumes a single leaf, uniform joints and no openings. Mortar is a simple geometric joint volume; it excludes frogs, hollow cores, bedding patterns, dry-mix conversion and waste. Confirm actual unit sizes.

Step-by-step takeoff workflow

  1. Enter your measured dimensions and inputs: Input the project values for Wall length (m), Wall height (m), Unit length (mm), Unit height (mm), Unit / wall thickness (mm), Mortar joint (mm), Wastage allowance (%). Check that every measurement uses the exact unit shown beside its field.
  2. Review the live quantity and formula calculation: The calculator applies Units = wall area / ((unit length + joint) × (unit height + joint)) immediately in your browser and displays the primary and secondary takeoff figures.
  3. Carry forward to cost, BoQ, CSV or printable takeoff sheet: Send your calculated quantity directly to Concrete Cost, Markup / Margin or the Bill of Quantities (BoQ) worksheet, or export via CSV and Print / PDF.

Worked example

A 6 m × 2.4 m wall has 14.4 m² of gross face area. Divide this by one unit’s face module, including the joint, then add the selected waste allowance.

Quick-reference lookup table

Quick reference: Standard single-leaf brickwork (215 × 65 × 100 mm metric module, 10 mm joint)
Wall face areaNet bricks (59.26/m²)Bricks with 5% wasteBricks with 10% wasteGeometric mortar (m³)
5 m² wall297 bricks312 bricks326 bricks0.085 m³
10 m² wall593 bricks623 bricks652 bricks0.171 m³
14.4 m² (6 × 2.4 m)854 bricks897 bricks939 bricks0.246 m³
25 m² wall1,482 bricks1,556 bricks1,630 bricks0.428 m³
50 m² wall2,963 bricks3,112 bricks3,260 bricks0.856 m³

Before you order

Compare the result with your drawings and supplier information. Keep the original net quantity separate from allowances, and round purchasing quantities only at the ordering stage. Check whether delivery, labour and related materials belong elsewhere in your estimate. If the drawing or specification changes, update the inputs and record the revised basis instead of reusing an earlier total.

For the concepts behind this calculation, read Wastage Factor, Takeoff (Quantity Takeoff), Unit Rate.

Common questions & estimating checks

What formula does the brickwork calculator use?

Units = wall area / ((unit length + joint) × (unit height + joint)) — Assumes a single leaf, uniform joints and no openings. Mortar is a simple geometric joint volume; it excludes frogs, hollow cores, bedding patterns, dry-mix conversion and waste. Confirm actual unit sizes.

How do you work out a brickwork example?

A 6 m × 2.4 m wall has 14.4 m² of gross face area. Divide this by one unit’s face module, including the joint, then add the selected waste allowance.

Which inputs and units are required for this calculation?

You enter Wall length (m), Wall height (m), Unit length (mm), Unit height (mm), Unit / wall thickness (mm), Mortar joint (mm), Wastage allowance (%). Keep metres and millimetres distinct, and use the header currency selector to display monetary amounts in EUR, GBP, USD or a custom currency code.

What should I check before ordering materials from a brickwork estimate?

Verify dimensions against approved construction drawings, confirm supplier pack sizes and product yields, and keep net measured quantities separate from cutting or site wastage allowances.