CONCRETE STRUCTURES

Concrete Stairs calculator

A solid stepped block, measured tread by tread.

YOUR MEASUREMENTS

Concrete Stairs

▱
↻ Results update as you type
YOUR ESTIMATELIVE
Concrete volume
2.618m³
Cubic yards3.424 yd³
CONNECT TO COST, LABOUR & BOQ
Open BoQ ↗

An estimate for planning. Currency selection changes the display symbol only (no exchange-rate conversion). Verify measurements and product specifications before ordering.

THE FORMULAVolume = width × tread × riser × n × (n + 1) / 2
ASSUMPTIONSAssumes solid fill under every step to a level base. This is not a suspended stair waist-slab calculation. Landings, foundations and wastage are excluded.
UNDERSTAND YOUR ESTIMATE

How to use the concrete stairs calculator

This calculator helps you calculate the concrete volume of a solid stepped stair block. It is intended for quantity takeoffs, early budgets and checks against a measured schedule. Start with the dimensions or quantities for one clearly defined item of work. Enter values in the units shown beside each field; millimetres and metres are not interchangeable.

Assumes solid fill under every step to a level base. This is not a suspended stair waist-slab calculation. Landings, foundations and wastage are excluded.

Step-by-step takeoff workflow

  1. Enter your measured dimensions and inputs: Input the project values for Number of steps, Riser height (m), Tread depth (m), Stair width (m). Check that every measurement uses the exact unit shown beside its field.
  2. Review the live quantity and formula calculation: The calculator applies Volume = width × tread × riser × n × (n + 1) / 2 immediately in your browser and displays the primary and secondary takeoff figures.
  3. Carry forward to cost, BoQ, CSV or printable takeoff sheet: Send your calculated quantity directly to Concrete Cost, Markup / Margin or the Bill of Quantities (BoQ) worksheet, or export via CSV and Print / PDF.

Worked example

Ten steps at 170 mm rise, 280 mm tread and 1 m width use 2.618 m³ in a solid stepped block.

Quick-reference lookup table

Quick reference: Solid stepped stair block volume (170 mm rise, 280 mm tread, 1.0 m width)
Number of steps (n)Total rise (m)Total going (m)Solid block volume (m³)Volume (yd³)
5 steps0.85 m1.40 m0.714 m³0.934 yd³
8 steps1.36 m2.24 m1.714 m³2.241 yd³
10 steps1.70 m2.80 m2.618 m³3.424 yd³
12 steps2.04 m3.36 m3.713 m³4.856 yd³
14 steps2.38 m3.92 m4.998 m³6.537 yd³

Before you order

Compare the result with your drawings and supplier information. Keep the original net quantity separate from allowances, and round purchasing quantities only at the ordering stage. Check whether delivery, labour and related materials belong elsewhere in your estimate. If the drawing or specification changes, update the inputs and record the revised basis instead of reusing an earlier total.

For the concepts behind this calculation, read Takeoff (Quantity Takeoff), Formwork, Concrete Grade.

Common questions & estimating checks

What formula does the concrete stairs calculator use?

Volume = width × tread × riser × n × (n + 1) / 2 — Assumes solid fill under every step to a level base. This is not a suspended stair waist-slab calculation. Landings, foundations and wastage are excluded.

How do you work out a concrete stairs example?

Ten steps at 170 mm rise, 280 mm tread and 1 m width use 2.618 m³ in a solid stepped block.

Which inputs and units are required for this calculation?

You enter Number of steps, Riser height (m), Tread depth (m), Stair width (m). Keep metres and millimetres distinct, and use the header currency selector to display monetary amounts in EUR, GBP, USD or a custom currency code.

What should I check before ordering materials from a concrete stairs estimate?

Verify dimensions against approved construction drawings, confirm supplier pack sizes and product yields, and keep net measured quantities separate from cutting or site wastage allowances.