MASONRY & FINISHES

Tile & Grout calculator

Tile counts and joint-fill volume.

YOUR MEASUREMENTS

Tile & Grout

▦
↻ Results update as you type
YOUR ESTIMATELIVE
Tiles to buy
59tiles
Geometric grout volume1.588 L
CONNECT TO COST, LABOUR & BOQ
Open BoQ ↗

An estimate for planning. Currency selection changes the display symbol only (no exchange-rate conversion). Verify measurements and product specifications before ordering.

THE FORMULATiles = ceil(area / tile area × (1 + waste / 100)); grout = joint-area fraction × area × depth
ASSUMPTIONSTile counts conservatively use tile face area without credit for joints. Grout output is wet joint volume, not product mass. Use manufacturer density and coverage guidance to order bags. Adhesive is excluded.
UNDERSTAND YOUR ESTIMATE

How to use the tile & grout calculator

This calculator helps you estimate tile counts and grout joint-fill volume. It is intended for quantity takeoffs, early budgets and checks against a measured schedule. Start with the dimensions or quantities for one clearly defined item of work. Enter values in the units shown beside each field; millimetres and metres are not interchangeable.

Tile counts conservatively use tile face area without credit for joints. Grout output is wet joint volume, not product mass. Use manufacturer density and coverage guidance to order bags. Adhesive is excluded.

Step-by-step takeoff workflow

  1. Enter your measured dimensions and inputs: Input the project values for Tiled area (m²), Tile length (mm), Tile width (mm), Joint width (mm), Grout depth (mm), Wastage allowance (%). Check that every measurement uses the exact unit shown beside its field.
  2. Review the live quantity and formula calculation: The calculator applies Tiles = ceil(area / tile area × (1 + waste / 100)); grout = joint-area fraction × area × depth immediately in your browser and displays the primary and secondary takeoff figures.
  3. Carry forward to cost, BoQ, CSV or printable takeoff sheet: Send your calculated quantity directly to Concrete Cost, Markup / Margin or the Bill of Quantities (BoQ) worksheet, or export via CSV and Print / PDF.

Worked example

20 m² covered with 600 mm square tiles requires 56 tiles before waste, or 59 tiles with a 5% allowance.

Quick-reference lookup table

Quick reference: Tile count (with 5% waste) and joint grout volume for a 20 m² area (3 mm joint, 8 mm depth)
Tile format (mm)Area per tileNet tiles (20 m²)Tiles with 5% wasteGeometric grout (L)
300 × 300 mm0.090 m²223 tiles234 tiles3.15 L
600 × 300 mm0.180 m²112 tiles117 tiles2.37 L
600 × 600 mm0.360 m²56 tiles59 tiles1.59 L
800 × 800 mm0.640 m²32 tiles33 tiles1.19 L
1200 × 600 mm0.720 m²28 tiles30 tiles1.19 L

Before you order

Compare the result with your drawings and supplier information. Keep the original net quantity separate from allowances, and round purchasing quantities only at the ordering stage. Check whether delivery, labour and related materials belong elsewhere in your estimate. If the drawing or specification changes, update the inputs and record the revised basis instead of reusing an earlier total.

For the concepts behind this calculation, read Wastage Factor, Takeoff (Quantity Takeoff), Unit Rate.

Common questions & estimating checks

What formula does the tile & grout calculator use?

Tiles = ceil(area / tile area × (1 + waste / 100)); grout = joint-area fraction × area × depth — Tile counts conservatively use tile face area without credit for joints. Grout output is wet joint volume, not product mass. Use manufacturer density and coverage guidance to order bags. Adhesive is excluded.

How do you work out a tile & grout example?

20 m² covered with 600 mm square tiles requires 56 tiles before waste, or 59 tiles with a 5% allowance.

Which inputs and units are required for this calculation?

You enter Tiled area (m²), Tile length (mm), Tile width (mm), Joint width (mm), Grout depth (mm), Wastage allowance (%). Keep metres and millimetres distinct, and use the header currency selector to display monetary amounts in EUR, GBP, USD or a custom currency code.

What should I check before ordering materials from a tile & grout estimate?

Verify dimensions against approved construction drawings, confirm supplier pack sizes and product yields, and keep net measured quantities separate from cutting or site wastage allowances.